图片三

当前位置: 网站首页 > 产品展示 > 试验仪器配套
试验仪器配套

ZM-15振磨机

ZM-15振磨机
  • 型号ZM-15型
  • 价格

详细描述

ZM-15振磨机


一、使用说明 Operating Instructions 
 
1. 装样Holding Sample
1.1 将冲击锤放入研磨盒中,再将样品放在研磨盒与冲击锤之间 Put impact rammer into the grinding case, and then put sample between grinding case and impact rammer.
1.2. 研磨盒中的样品量为515cm 3 Quantity of sample in grinding case shall be 515cm3.
〈警告〉当放入研磨盒中的样品量≤5cm 3时,会损坏研磨盒。 In case quantity of sample put into the grinding case is ≤5cm3, it may damage the grinding case.

2. 时间设定Time Setting
2.1. 按时间继电器上下两行按纽,设定运行时间。其中中间的一位表示时间单位:小时(H)、分钟(M)和秒(S)。Press two buttons at upper and lower rows on the Time Relay, set the running time, of which the middle digit indicates time units: hour (H), minutes (M), and seconds (S).
2.2. 碳化钨的研磨盒,一般设定在3分钟之内,高铬钢的研磨盒,一般设定在10分钟之内Generally set within 3 minutes for grinding case of tungsten carbide, 10 minutes for that of high chrome.

3. 制样 Specimen Preparation
3.1. 将研磨盒放在振动磨的固定盘上,旋紧固定手柄。

2。盖紧振动磨的盖,按振动磨的绿色启动按钮。启动振动磨Put the grinding case on the fixed disk of Vibration Grinding Mill, screw the fixed handle.2. Fasten down the cover of Vibration Grinding Mill, press green start button of it. Start Vibration Grinding Mill.
3.2. 如果发生意外情况,请立即按下红色急停按钮If something unexpected happened, please press red emergency stop button immediately.
〈警告〉在机器完全停稳前,不要打开振动磨的盖。 Do not open the cover of Vibration Grinding Mill before the machine completely stopped.

3.3. 机器停稳后,打开振动磨的盖,取出研磨盒。将样品倒入过滤筛中,应有80%样品的粒度≤80umAfter the machine completely stopped, open the cover of Vibration Grinding Mill, take out the grinding case. Pour sample into filter sieve, particle size of 80% sample should be in ≤80um.
3.4. 如果研磨后的样品,达不到3.3. 的要求。取出研磨盒,自然冷却至60℃以下,再继续工作。并找出最佳研磨时间In case the sample after grinded can’t reach the requirement described in Item 3.3, take out the grinding case, cool it to less than 60℃ in room temperature, and work continuously. Find out optimum grinding time.

 

二、技术指标 Indicators

 

名称

技术参数

进料粒度

10mm3

出料粒度

 80um(或200目)

进 料 量

10  30cm3

   

380V

额定功率

1.5 KW

   

1400r/min

研磨时间

0999

磨盒容积

100cm3

磨盒材料

碳化钨或高铬钢

外型尺寸

610 x 550 x 890mm

   

220

分享到:
点击次数:  更新时间:2016-07-21 09:18:13  【打印此页】  【关闭
上一条:没有了  下一条:多用途跌落试验机